How to Use Metal Framing Materials - DIY Home Improvement Guides - How to Repair and Remodel your Bathroom, Kitchen and more

Home

Community

Home Improvement

Outdoors

Finishing

Storage

Tools & Techniques

Lighting

Tips

Search all of RonHazelton.com:

Housecalls on TV |

Sweepstakes

[Log In]

Related Articles

How to Install A Pre-Assembled Attic Stairway

How to Create Recessed Shelving in a Wall

How to Build a Slide-out Pantry

How to Install a Porch or Deck Railing

How to Build a Wooden Mailbox

How to Install a Slatwall Shelving System

How to Install a Wood Stair Railing Kit

How to Make a Cutting Board

How to Create Decorative Wall Panels

How to Install New Kitchen Cabinets

Home Improvement > Walls > How to Use Metal Framing Materials

Learn how to frame a wall with metal framing studs and channels.

View the Video

Metal framing studs compare favorably with conventional wooden construction studs and are now available at your home improvement store. The steel studs are lightweight, strong and uniformly straight and true. Metal framed walls use a track or channel at the top and bottom to hold the studs in place, but the basic wall frame construction is the same. Working with them requires only two tools: a power drill and a pair of snips. Basic installation instructions are available below.

Step by Step Instructions and Video

View the Video
Metal framing studs compare favorably with conventional wooden construction studs and are now available at your home improvement store. The steel studs are lightweight, strong and uniformly straight and true. Metal framed walls use a track or channel at the top and bottom to hold the studs in place, but the basic wall frame construction is the same. Working with them requires only two tools: a power drill and a pair of snips. Basic installation instructions are available below.

Snip Through the Channel Sides/Legs First
Hold the track on edge and snip through the sides/legs first to begin cutting the channels to the correct length for the wall frame you are constructing. The cut metal edges may be sharp, so wear leather gloves to avoid nicks and cuts.

Let the Scrap End Bend Back on Itself
Rotate the track with the severed sides/legs upward and let the unsupported weight of the scrap end drop and bend the face of the channel back on itself.

Finish Cutting the Face with the Snips
Finish severing the two pieces of track along the bend with the metal snips while squeezing the sides/legs together with one hand and cutting with the other.

Attach the Length of Channel to a Wooden Base or Subfloor
Attach the length of track to a wooden base or subfloor with drywall screws. You can also assemble the wall frame with it lying flat on the floor, stand it upright in position, and then anchor it to the floor.

Slide the Metal Stud into Position
Insert the metal studs into the channel, sliding them into position and observing building codes for spacing. Avoid making an obstacle of the installed studs. Work from the middle outward to both ends of the channel or ensure that you slide each successive stud into the track from the same end of the channel.

Secure the Studs with Pan-head Screws
Secure the studs with short pan-head screws with self-drilling tips. Drive them through the outside of the channel into the side of the studs.

Position the Top Track Over the Studs
Set the top track over the secured studs and drive pan-head screws through each to secure them at the upper end.

Insert Plastic Gromets to Protect Wire Runs
Insert large plastic grommets into the pre-punched holes in the studs to facilitate running electrical wiring and protecting it from nicks and cuts.

Apply Drywall with Special Screws
Apply drywall in much the same way as conventional framing, but use special screws with finer threads designed to pierce the metal studs.

Home | Contact Us | Advertising & Product Placement | Media Inquiries | Privacy | Terms of Use | Pages Index
2009 Ron Hazelton Productions - Do It Yourself Home Improvement - All Rights Reserved
Website Design by Jonathan Preston and Mark Godwin
Page generated in 0.516 seconds