Transcript

Design, build and Finish a Custom Picture Frame in a Few Simple Steps.

Add a personal touch to a photograph, print, or piece of art by designing and building your own picture frame. Taking the time to create your own will allow you to design a frame that fits your decor, the nature of the artwork, as well as give you the satisfaction that comes with doing it yourself.

Read More
Ripping the stock to size with a table saw
Step 1

Select the Material for Your Frame

For this project, Ron is using poplar. This hardwood is readily available at most home improvement stores, and is fairly versatile. To build this frame, you will need three different thicknesses, but if you'd like a frame with a little more (or less) heft, then you can be flexible with the thickness of the wood that you choose. Obviously, a heaver frame may be more appropriate for a larger piece. Once you've selected the thickness of your stock, use a table saw to rip it to the correct width.

Rounding the corners off of the thickest pieces of stock
Step 2

Round the Edges of the Frame Stock

When building a custom frame, you can add your own unique design touches by rounding and shaping the pieces of stock that you assemble. A router and a router table are the easiest way to do this. A round-over bit will eliminate any sharp edges and give the framework a smooth, sculpted look and will help hide the transitions between the pieces.

Using spring clamps to hold the frame while the glue dries
Step 3

Glue and Clamp the 1st set together

When gluing two flat pieces together, make sure that the glue is spread into a thin even layer. This will ensure that the bond is tight and will stand the test of time. Once the glue is spread over the appropriate area, apply a spring clamp every 6 inches or so. If you have to use heavier clamps, make sure you use a piece of wood between the jaws of the clamp to disperse the force, otherwise you will have marks and indentations on wood and they will show on your finished frame.

Cutting the rabbit for the picture glass
Step 4

Create the Contours of the Frame

Once the glue has dried, you can use another style of router bit to remove the corner where the two pieces of wood are glued together. This will make the frame look as though it's one solid carved piece of wood. Use a cove box bit to create the smooth, round face of the frame. After you've shaped the face, change the bit again to a square router bit and cut a rabbit joint on the back side. Make it deep enough to hold the glass that will go over the front of your painting, photograph or other artwork.

Using a simple jig to hold the stock in place on the router table
Step 5

Completing the Frame Stock

The third piece of stock that you are going to add to the picture frame stack is fairly thin compared to the two others. To ensure that you can run it through the router table safely, you'll need to construct a simple jig. The purpose of the jig is to hold keep the stock in place, without you having to place your fingers too close to the router bit. The jig can be several pieces of scrap wood that are clamped into place with spring clamps. After the 3rd piece of stock is shaped with the router, glue it into place and let it dry while clamped.

Attaching a wooden extension to the miter gauge
Step 6

Miter the corners

Using a table saw to cut the miters for the frame ensures accuracy and safety. Use a miter gauge to ensure that the angle is correct and uniform for all of the joints. A stop block will guarantee that all of the frame pieces are the same length. This is vital if they are going to line up correctly when you try to put them together.

Explaining how the gluing jig works
Step 7

Build a jig to glue the frame together

You will find that it is much easier to build a frame that is square and true if you construct a jig to help you line the pieces up correctly for gluing. Simply nail or screw a square piece of stock to the bench, and then use the square corners to make sure that your frame joints are lined up perfectly. Once you have the jig ready, apply a generous amount of glue to the corners, set them together around the jig, and then fasten them with a pin nailer.

Setting a glazier's point on the screwdriver
Step 8

Framing the Picture

After the glue has completely set and you've had a chance to stain, paint, or finish the frame the way that you want, you are ready to put in the picture. First, set the glass into place in the rabbit that you cut on the back side of the frame. Then, you can set the matted picture into place behind the glass. Use glazier's points to hold the glass and picture in place. Once it is secure, tape craft paper over the back of the frame to help protect the picture inside.

comments

Related Tips

Blog Articles

December 30, 2017

How Custom Baseball Bats are Made

A custom baseball bat maker on Cape Cod creates tailor-made bats for amateurs and pros alike.

December 01, 2017

How Fortune Cookies are Made

My visit to a San Francisco fortune cookie bakery

November 18, 2017

Trompe-l’œi - The Art of Illusion Brought Home

A visit to a trompe-l'œi artist's home where what meets the eye may be misleading.

Recent Articles